Zombie - 90 L series sedan
- last celtic warrior
- Junior Member
- Posts: 271
- Joined: Mon Aug 06, 2007 9:39 pm
- Location: Gympie, Queensland
Zombie - 90 L series sedan
Needed a temporary car until the Tank is back in action, so took a chance on a $200 L series that caught my eye on gumtree. The motor was seized and thoroughly dead though...
When I got there with a trailer, I had a look from the top of the motor and all i could see was underbody spray all over everything with some silverfrost on a few details to make it look like a motor still. The body has also been accentuated with areas of underbody spray, around the windscreen, front edge of bonnet, grill, bumpers and everything from the waiste down. Guy must have owned a tar factory.
Once I pulled the odd shaped lump out of the engine bay, I decided I just had to pick the scab. I didn't really know where to start, since everything from the middle of the valve covers down was one big abstract shaped crusty scab. Once I chipped away at it and started bravely pushing my fingers into the rotten mess inside, I then managed to tear a chunk loose and see that there really was still an engine under all the red silicone, bit of blue silicone, lots of black silicone, some white bathroom sealant, pockets of half set grey bog, and layers of underbody spry and paint...
The front bumper was another little surprise, when I peeled off some of the grey plastic that had been glued in bits over the whole surface. Yes, it was stuck together inside with scraps of pine and chipboard and heaps of hard-as-nails. Even my xray vision didn't see THAT coming...
Nothing's ever as bad as it looks though. The motor is now completely stripped down and it turns out the previous "mechanic" had poured a bottle of form-a-gasket into the oil to try and stop some of the leaks the his inbuilt drip tray couldn't. THAT'S what had seized the motor. Every big end, main, gudgeon, cam, piston oil ring, etc had been glued solid once the form-a-gasket had got nice and hot. Amazingly, the brown scale scraped off with a firm thumbnail and all surfaces are like new still. I've ordered a full gasket kit and this engine is going back together... PROPERLY this time. There's not even any wear on the pistons, bores or oil pump.
Ok, signing off to go get oily again. I'll post more soon...
When I got there with a trailer, I had a look from the top of the motor and all i could see was underbody spray all over everything with some silverfrost on a few details to make it look like a motor still. The body has also been accentuated with areas of underbody spray, around the windscreen, front edge of bonnet, grill, bumpers and everything from the waiste down. Guy must have owned a tar factory.
Once I pulled the odd shaped lump out of the engine bay, I decided I just had to pick the scab. I didn't really know where to start, since everything from the middle of the valve covers down was one big abstract shaped crusty scab. Once I chipped away at it and started bravely pushing my fingers into the rotten mess inside, I then managed to tear a chunk loose and see that there really was still an engine under all the red silicone, bit of blue silicone, lots of black silicone, some white bathroom sealant, pockets of half set grey bog, and layers of underbody spry and paint...
The front bumper was another little surprise, when I peeled off some of the grey plastic that had been glued in bits over the whole surface. Yes, it was stuck together inside with scraps of pine and chipboard and heaps of hard-as-nails. Even my xray vision didn't see THAT coming...
Nothing's ever as bad as it looks though. The motor is now completely stripped down and it turns out the previous "mechanic" had poured a bottle of form-a-gasket into the oil to try and stop some of the leaks the his inbuilt drip tray couldn't. THAT'S what had seized the motor. Every big end, main, gudgeon, cam, piston oil ring, etc had been glued solid once the form-a-gasket had got nice and hot. Amazingly, the brown scale scraped off with a firm thumbnail and all surfaces are like new still. I've ordered a full gasket kit and this engine is going back together... PROPERLY this time. There's not even any wear on the pistons, bores or oil pump.
Ok, signing off to go get oily again. I'll post more soon...
Steve.
- BARNES AUTOMOTIVE TECHNOLOGIES -
- BARNES AUTOMOTIVE TECHNOLOGIES -
- 60766244
- Junior Member
- Posts: 586
- Joined: Fri Nov 09, 2012 3:32 pm
- Location: Kalamunda, Western Australia
The chipboard is a new one!!
Otter the 2004 Outback with all the fruit.
Possible Improvements: Rigid 12db Phone Aerial Fitted, Air-compressor w/ Hose & Air-Tank, Jerry Holders, Lift, Nudgebar and Spots?
|| Ausubaru Wiki: New AUSubaru Wiki, About the Wiki || My Ex, Maple the Brumby, Rack, Lift Kit, Raptor-Liner Tray || Shed: Benches ||
Possible Improvements: Rigid 12db Phone Aerial Fitted, Air-compressor w/ Hose & Air-Tank, Jerry Holders, Lift, Nudgebar and Spots?
|| Ausubaru Wiki: New AUSubaru Wiki, About the Wiki || My Ex, Maple the Brumby, Rack, Lift Kit, Raptor-Liner Tray || Shed: Benches ||
- Silverbullet
- Senior Member
- Posts: 2870
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
- Rodeo4jake
- Junior Member
- Posts: 297
- Joined: Fri Oct 19, 2012 5:42 am
- Location: Tylden Victoria
- El_Freddo
- Master Member
- Posts: 12506
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Bridgewater Vic
- Contact:
Well, I reckon it would have helped keep the oil in these EA82s! They certainly know how to leak like a sieve!Rodeo4jake wrote:Well just when you think you've seen it all something comes along & trumps it. Unbelievable, I've never seen bitumen spray used to that extent before. Form a gasket in the engine, must've thought it would work like tyre sealant.
I hope the work all goes well. It looked like such a clean unit for $200! I guess there was a catch...
Cheers
Bennie