Rear diff protector

RSR 555 · Post by **RSR 555** » Mon Apr 28, 2014 10:00 pm

I have some rear diff protectors. If anyone wants one they are $55 plus postage

taza · Post by **taza** » Tue Apr 29, 2014 2:39 pm

What do they fit?

RSR 555 · Post by **RSR 555** » Tue Apr 29, 2014 3:55 pm

Good point, they will fit any R160 & R180 diffs. First post fixed

steptoe · Post by **steptoe** » Tue Apr 29, 2014 6:30 pm

Were the Uglies in that category ? I think my diff protector was off an ugly and needed some mods to fit.

AndrewT · Post by **AndrewT** » Tue Apr 29, 2014 6:40 pm

I might have to get one of these but maybe somehow a thicker one.
I have one (original off an old RX sedan) and I smashed it on a rock once - it bent up and smashed itself into the diff lol. Maybe it did still save the diff still though, the diff was fine after all!

RSR 555 · Post by **RSR 555** » Tue Apr 29, 2014 11:07 pm

I've not measured the ugly series diff but I have my ute here, so I'll check it out and report back.

These protector plates are 5mm think unlike the original Subaru ones that were 3mm

ccspeed · Post by **ccspeed** » Fri May 02, 2014 8:53 pm

Not sure if my diff is the one of the listed diffs above, but if it'll fit a 1990 brumby i'm interested. Could you let me know postage to 5154 south australia, cheers

YouTube · Post by **El_Freddo** » Sat May 03, 2014 10:06 am

Ooh, tempting...

I really need to work on my bash plate before I look at the rear diff... I smashed my exhaust extractor on the driver's side pretty hard last weekend - cracked a factory weld on the exhaust manifold

Cheers

Bennie

Corax · Post by **Corax** » Sun May 04, 2014 8:03 pm

One of the original 3mm ones just sold on ebay for $177.50 and no I'm not kidding! Not trying to give you ideas Paul, as I will probably buy one off you for my brumby next time im up in your neck of the woods. No idea when that'll be though.

FujiFan · Post by **FujiFan** » Sun May 04, 2014 9:35 pm

One of the original 3mm ones just sold on ebay for $177.50 and no I'm not kidding!

In the words of Mr T, I pity the fool!

90brumby · Post by **90brumby** » Mon May 05, 2014 3:44 pm

Paul can you please put another aside for me, ill have to put one on the new foz, ill get it off you when our swings line up

Cheers

rtcb65 · Post by **rtcb65** » Mon May 05, 2014 6:09 pm

Hey Paul, Just to let you know, if fit brumby,M.Y. , Liberty/outback gen1 &2, they wont fit gen 3 . Totally different mounting.

The diff protectors are almost a carbon copy of the CROSS B R E D PERFORM ANCE ones.

ccspeed · Post by **ccspeed** » Tue May 06, 2014 9:30 am

Any word on the protector yet? Still interested.

RSR 555 · Post by **RSR 555** » Tue May 06, 2014 12:34 pm

Corax wrote:One of the original 3mm ones just sold on ebay for $177.50 and no I'm not kidding! Not trying to give you ideas Paul, as I will probably buy one off you for my brumby next time im up in your neck of the woods. No idea when that'll be though.

Thanks Dave but I'm selling these for what they owe me. As most people know, I'm not looking to retire off my parts or service

90brumby wrote:Paul can you please put another aside for me, ill have to put one on the new foz, ill get it off you when our swings line up

Cheers

Can do buddy

rtcb65 wrote:Hey Paul, Just to let you know, if fit brumby,M.Y. , Liberty/outback gen1 &2, they wont fit gen 3 . Totally different mounting.

The diff protectors are almost a carbon copy of the CROSS B R E D PERFORM ANCE ones.

Thanks Rick, I'm pretty sure you're correct as my friend gave me back the one I sold him for his 03 Outback. I will have to see what is required to fit to the later models.

I'm not sure what the xbread ones look like, so I'll take you're word on that. I can make changes to them if needed but I had 10 made up, so won't worry about it for this lot.

ccspeed wrote:Any word on the protector yet? Still interested.

Yeah, sorry for delay, just read your post and will find out for you toady the cost of postage.

jayrod · Post by **jayrod** » Sat May 17, 2014 10:31 pm

Ill snap one up aswell if u got any

RSR 555 · Post by **RSR 555** » Thu May 22, 2014 10:36 pm

rtcb65 wrote:Hey Paul, Just to let you know, if fit brumby,M.Y. , Liberty/outback gen1 &2, they wont fit gen 3 . Totally different mounting.

Ok Rick, just had a look at the Gen3 and just need to bend them slightly to miss the diff mount and they will fit perfectly. I'll be doing one up for a friend shortly, so I'll post up the pics.

ccspeed wrote:Any word on the protector yet? Still interested.

Forgot all about this sorry, so I'll get my son to measure up and weigh it, so I can give you a quote for postage.

jayrod wrote:Ill snap one up aswell if u got any

I have about 10 left, so no worries

The ALL NEW AUSubaru.com.au Forums

Rear diff protector

Rear diff protector for R160 & R180 models