My Vortex Project

Show off your Subaru to other members. Tell us a bit about it. What mods you have done or have planned for the near future.
Post Reply
User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Sun May 04, 2014 1:49 pm

Thanks for the reply again Steptoe

A grand (roughly) seems a bit much but what can you do, it would be nice if there was second hand ones I can buy hahaha, but looks like I'll have to make a swap over to the standard suspension, is there any other ways (less expensive ways) to have adjustable suspension or would that cost more to do than repairing the original system (just weighing up my options), lucky enough for me that I have another car to get me around and this is my project car, just cant wait to get it on the road so I can drive it once again.


Once again, thanks for all the help

Kind regards
Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
FujiFan
Junior Member
Posts: 494
Joined: Sun Oct 31, 2010 8:32 pm
Location: CentralCoast NSW

Post by FujiFan » Sun May 04, 2014 9:47 pm

As for the suspension it is an air bag system
There was a used set listed on fleabay Oz a few weeks ago described as being from RX turbo sedan, cant recall starting bid.

User avatar
El_Freddo
Master Member
Posts: 12487
Joined: Tue Oct 04, 2005 10:00 am
Location: Bridgewater Vic
Contact:

Post by El_Freddo » Sat May 10, 2014 6:21 pm

FujiFan wrote:There was a used set listed on fleabay Oz a few weeks ago described as being from RX turbo sedan, cant recall starting bid.
I thought it was gumtree, but anyway.

Johnny, what you can do is easily swap to coils, disconnect the power/fuse to the air pump and keep all of the system in the vehicle - then you can buy/source/find/steal/whatever to get the airbags sorted in your own time. This will help save on the $$$ needed for the airbags - who knows, you might find a way of replacing the airbag component only :twisted:

There are options, don't ditch stuff before you find out what you can/can't do with it.

Cheers

Bennie
"The lounge room is not a workshop..."
Image
El Freddo's Pics - El_Freddo's youtube

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Sun May 11, 2014 11:13 am

Thanks for the advice again El Freddo, when I get some free time on the weekend (lucky for me I found a new job) I'll try and swap over the system and keep the old suspension stored till I get more cash in the bank hahaha.

If everything goes according to plan I should have the car started this year.


Thanks again for all the feedback.

Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
El_Freddo
Master Member
Posts: 12487
Joined: Tue Oct 04, 2005 10:00 am
Location: Bridgewater Vic
Contact:

Post by El_Freddo » Fri May 16, 2014 7:08 pm

Johnny T wrote:If everything goes according to plan I should have the car started this year.
That's a big statement :rolleyes: :p

Cheers

Bennie
"The lounge room is not a workshop..."
Image
El Freddo's Pics - El_Freddo's youtube

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Tue May 20, 2014 11:23 am

hahaha hopefully it can be done,

I have found someone who can make new Sunraysias wheels with the 4x140 stud pattern for $75.00 per rim, if I get some time this weekend I can check it out and see if its any good, but are these rims worth $75.00each? also what is the standard width of these rims because I would like to fit 205 width tyres on the car once its fully complete.

Thanks again for all the feed back,

Kind regards
Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
steptoe
Master Member
Posts: 11582
Joined: Thu Oct 06, 2005 10:00 am
Location: 14 miles outside Gotham City

Post by steptoe » Tue May 20, 2014 1:57 pm

hard thing to quantify the worth when compared to mass churned out in China alloy wheels that don't fit our Subes. If you have found someone that can custom make you a set of five if you can afford and at $75 each, they are a bargain.

Can they do them in a choice of 13,14 and 15's ?

You might have to work with them to work out not only how wide the rim is but its inside and outset measure off centre/off set etc.

Have us tell you and sumptin' goes wrong .....

User avatar
H-top
Junior Member
Posts: 782
Joined: Thu May 22, 2008 4:27 pm
Location: Brisbane

Post by H-top » Tue May 20, 2014 4:48 pm

I've got some 14s for sale
H-Top

rolling in

MY00 GT Foz - Auto, Turbo, Luxury

Image

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Wed May 28, 2014 3:56 pm

Thanks for the reply guys, I think they make them 14" if I have some free time this weekend I will find out where they are made and ask them if they make them to any size.

Once I find out all the information I will post it back on here and if everyone likes the sound of the measurements and possible wheel size I can put a contact details up :)

Also H-top, thanks for the offer, I think the transport cost will cost me an arm and a leg from Brisbane To Melbourne hahaha

I will keep everyone posted once I finish up.

Thanks again for the reply's,

Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Sat Jun 21, 2014 4:45 pm

Hey everyone, its been awhile since I've been here, I have been looking for a new ignition barrel as mine couldn't be repaired, I tried contacting a few places and didn't have any luck as they don't stock / make them anymore.

Lucky enough I contacted Import Monster and amazingly they were able to track one down for me from Japan, its about 6 - 8 weeks away, they also found for me a Dash Trim and its still in once piece, so I'm pretty happy about the find, now I am just waiting too see if they have a radio :)

Here is a photo of the Trim
Image

I have spoken to a Subaru Mechanic Specialist in Clayton and he is going to see if he still has his air suspension as he said it still works but not sure where it is, fingers crossed I'll be able to get a replacement.

On other things I would like to know when I get my car ready to start again (its been 3 years since the engine cranked over), what engine oil I should I use as the car has only done 156,000km on it and what else should I do before I turn the engine over?

Thanks again for everyone's help :)

Kind regards
Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
steptoe
Master Member
Posts: 11582
Joined: Thu Oct 06, 2005 10:00 am
Location: 14 miles outside Gotham City

Post by steptoe » Sat Jun 21, 2014 5:27 pm

that trim needs to find its way into a 3D printer studio !!

i use 15w40 in ea82, thinking 10w40 might be needed for winter temps

User avatar
Willy Fisterbottom
Junior Member
Posts: 330
Joined: Wed Feb 26, 2014 9:37 am
Location: NSW

Post by Willy Fisterbottom » Sat Jun 21, 2014 7:30 pm

I have five Vortexes and only one has a good dash trim :-(

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Sun Jun 22, 2014 3:45 pm

Thanks for the advice steptoe, really appreciate it :)

if I get some time to take to a 3D printer place, would they be able to remake it without damaging the original piece? I will also get a price to see how much it would cost to remake them as we'll, if I get a ruff idea on how many to make that should lower the price :) once I get my parts I'll post another update, just can't wait hahahaha
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
El_Freddo
Master Member
Posts: 12487
Joined: Tue Oct 04, 2005 10:00 am
Location: Bridgewater Vic
Contact:

Post by El_Freddo » Sun Jun 22, 2014 7:33 pm

That's an awesome find mate!

I can see why they crack or get damaged easy!

I hope the 3D printing turns out, I reckon you might have a few lining up depending on price and finish quality.

Cheers

Bennie
"The lounge room is not a workshop..."
Image
El Freddo's Pics - El_Freddo's youtube

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Mon Jun 23, 2014 2:33 pm

Thanks Bennie,

Import Monster have been awesome for tracking down that part for me and if I can help make a model for everyone I'll be more than happy to get quotes from a 3D printer place, you just never know if there is another one of these in this condition.

I'm going to ask Import Monster if they can get me the sun roof gutters because mine have completely rusted out, would it be a good idea if I can get the gutters made from the 3D printer as well or would it all have to be made out of steel because if I have parts that can be remade I would like to help anyone out that needs it :)

After I get some quotes for the trim, its going to be stored in a box with bubble wrap so it doesn't get damage :)
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Thu Oct 02, 2014 8:22 am

Hey guys,

Just a quick update, I have received all the parts from Japan, when I get some time off I will take the trim to a 3D printer place so I can get a few extras made if anyone is interested :)

On the other news my Uncle and I are almost done putting the engine back together and we just need to know for the spark plug leads what the firing order is, because I will be able to have the car started up this weekend after 3 long years :)
I have looked in the repair manuals found on the forum and can't seem to find it (or I have been looking in the wrong spots :S )

Any help would be appreciated

Thanks guys and will post and update this weekend

Kind regards
Johnny T
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Wed Jan 07, 2015 6:25 am

Hey everyone, just a quick update,

I have the eninge block back together and having an issue with replacing the fuel pump, when I removed the old one and put in a bosh 910 pump it didnt fit (as I purchased thia pump awhile ago and the guy at the shop said it would fit)

I have been to a few autoshops and they found a Walbro pump from PAT or a External hp from Fuelmiser.

Does anyone know what will fit as I would like to have the car started as soon as possible.

Any help would be great, thanks everyone :)
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
steptoe
Master Member
Posts: 11582
Joined: Thu Oct 06, 2005 10:00 am
Location: 14 miles outside Gotham City

Post by steptoe » Wed Jan 07, 2015 6:40 am

what dont fit ? pump not fit in bracket or hoses dont fit? or electrical plug ?

User avatar
Johnny T
Junior Member
Posts: 276
Joined: Mon Mar 08, 2010 10:06 pm
Location: VIC - Frankston Area

Post by Johnny T » Wed Jan 07, 2015 12:02 pm

Thanks for the reply Steptoe, the pipe to the tank didn't fit and the pipe to the fuel lines (connecting to the engine bay area) didn't fit aswell, what would be the best thing to do?
________________________________________
Johnny T
88kw of fun waiting to happen

User avatar
steptoe
Master Member
Posts: 11582
Joined: Thu Oct 06, 2005 10:00 am
Location: 14 miles outside Gotham City

Post by steptoe » Mon Jan 12, 2015 11:43 pm

a universal efi pump with specs to match - don't buy or pay anyone for one unless they can provide hose connection types and sizes.

You need an external efi pump with 1/2" intake 8mm outlets. Check out Nardek in Sydney via a google search

Post Reply

Return to “My Subi”