Page 1 of 1
C.V cups and splines
Posted: Mon Jul 21, 2008 7:02 pm
by SubaRute
who out there knows,what liberty has a 22spline on the CV shaft,im looking for the right ball and case with a 22 spline and the cup to fit a liberty g/box,im told all lib g/boxs are 25 spline off the cup,please dont get
confused with the cup spline it the 22 ball and casing im chaseing where and what model subaru lib it comes from?
thanks leon
Posted: Tue Jul 22, 2008 10:00 am
by Subaman
What exactly are you trying to do mister? It might be easier to understand and help you easier.
Cheers
Grant
Posted: Wed Jul 23, 2008 12:44 pm
by El_Freddo
I've never heard of a liberty gearbox with a 22 spline cup, its typically 25 spline or 23 spline in the old L's AFAIK, but the rear diff should be a 23 spline cup in the early libs, up to what year I don't know I'm sorry.
If your after a front unit, the Carbie L series front shaft inner cups should do the job as they are all 22 spline on the cup, you 'll need to swap the shaft or the cage in the cup to make it fit. I'm not sure about which one to swap as I've never done it before.
Cheers
Bennie
Posted: Wed Jul 23, 2008 7:59 pm
by SubaRute
ok on the CV shaft i have,(MYshaft) has a 23 spline(not 22) so the cup spline for a lib g/box is 25.
what model liberty cup will fit my CV shaft?(MY,CV shaft)
another ej22 conversion,lib g/box and MY running gear
Posted: Wed Jul 23, 2008 8:37 pm
by El_Freddo
SubaRute wrote:ok on the CV shaft i have,(MYshaft) has a 23 spline(not 22) so the cup spline for a lib g/box is 25.
what model liberty cup will fit my CV shaft?(MY,CV shaft)
another ej22 conversion,lib g/box and MY running gear
Okay, making more sense now.
What you need is the
Inner CV cups from an MPFI touring wagon. You should grab the cage too if not the whole shaft to play with. The Inner cup should fit the liberty cage without a problem. The spline count will be the same too, which is what your after.
Good luck
Cheers
Bennie
Posted: Wed Jul 23, 2008 9:59 pm
by SubaRute
thanks
so thet meens that the MPFI shaft is a 23 spline(on the ball and cage as well) and the cup has a 25 spline.
thanks again.
Posted: Thu Jul 24, 2008 7:51 am
by Subaman
The MPFI cup is only 23 spline, you could use the MPFI balls and cage with a 2wd Liberty cup or an rx CUP.
Posted: Thu Jul 24, 2008 12:45 pm
by El_Freddo
Subaman wrote:The MPFI cup is only 23 spline
That's not been my experience - MPFI and MPFI turbo cups are 25 spline, with the turbo cup being larger for the extra stress of the turbo's torque...
Bennie
Posted: Thu Jul 24, 2008 6:31 pm
by Morcs
Talk to someone that specialies in drive shafts etc they can build any thing that you want in a shaft and have access to all the right information new front drive shafts new cvs both ends ej turbo gearbox standard to brumby outers only cost me $165 each with a warranty. I thought money well spent as he made sure they were balanced
as well.
Posted: Fri Jul 25, 2008 12:42 am
by mattl200
23 spline on the shaft not the cup
u can use rx turbo inners on the shafts u got
there 25 spline on the cup
Posted: Fri Jul 25, 2008 10:58 am
by Subaman
The MPFI cup is only 23 spline, you could use the MPFI balls and cage with a 2wd Liberty cup or an rx CUP.
Sorry Leon, ment to say the MPFI turbo auto cup is only 23 spline, you could use the MPFI turbo auto balls and cage with a 2wd Liberty cup or an rx CUP.
Or just run complete RX shafts