L-series - liberty motor info
L-series - liberty motor info
hi got a question that has been on my mind for awhile now. i have an L-Series touring wagon thats EFI not carb and i was wondering would the fact that it is an EFI model make it easier to fit a 2.2 litre liberty motor than a carb model? what is involved in fitting a 2.2 motor to an L? do they bolt up to the standard L gearbox? can you use the wiring harness that is in the car? i am assuming that a 2.2 motor would be a better option than an EA 82 turbo motor. i am thinking that the turbo motor would not be as torquey off the mark due to lag and the fact that turbo motors atre usually lower compression. is this the case or have i got it all wrong. anyway any help would be great.
- Suby Wan Kenobi
- General Member
- Posts: 1914
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Sunny Godwin Beach Qld
NO they wiring is different you would have to either pick out the EJ22 motor loom and then pick your ea engine control out and splice together your new loom. Or remove your Lseries loom and put in a carb loom and then lay the EJ22 loom over it. And the gearbox to motor has a different pattern however Brett can sell you an adaptor if you need one
[SIGPIC][/SIGPIC]
The long road ahead
The long road ahead
Fitting an EJ motor to an EFI L series is easier than fitting one to a carby model.
1 - the fuel system is already done.
2 - the wiring is easier because you can splice the EJ loom straight into the EA loom where the existing ecu connectors are - easier than finding all the separate wires in the carby models.
You will have to use the EJ22 wiring loom and ECU and run it at the same time as the EA loom. There are only about 10 or so wires that need to be spliced in. There are places that will cut the EJ loom down for you and send it to you complete with fitting instructions specifically for plugging into an L series...
No it won't bolt up to the existing gearbox but you can just use an adaptor plate for this. Either make one or buy one from BYB.
You are spot on with your thinking about torque/quickness off the line etc. I think the EJ22 is a better option than the EA82turbo. The EA82turbo will be slightly faster overall but have much more chance of failing (older motors, older design, its an EA!).
EJ22 into L series is an easy and affordable conversion - do it!
1 - the fuel system is already done.
2 - the wiring is easier because you can splice the EJ loom straight into the EA loom where the existing ecu connectors are - easier than finding all the separate wires in the carby models.
You will have to use the EJ22 wiring loom and ECU and run it at the same time as the EA loom. There are only about 10 or so wires that need to be spliced in. There are places that will cut the EJ loom down for you and send it to you complete with fitting instructions specifically for plugging into an L series...
No it won't bolt up to the existing gearbox but you can just use an adaptor plate for this. Either make one or buy one from BYB.
You are spot on with your thinking about torque/quickness off the line etc. I think the EJ22 is a better option than the EA82turbo. The EA82turbo will be slightly faster overall but have much more chance of failing (older motors, older design, its an EA!).
EJ22 into L series is an easy and affordable conversion - do it!
EZ30 L series - Monsterwagon
https://www.ausubaru.com.au/viewtopic.php?f=71&t=26163
https://www.ausubaru.com.au/viewtopic.php?f=71&t=26163
- Suby Wan Kenobi
- General Member
- Posts: 1914
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Sunny Godwin Beach Qld
apart from 4wd starts (eg boggy stuff) which are ok but sometimes annoying the ea82t is great fun driving round in my opinion-but ive never driven anything else. i dont know but itd probably be cheaper to add a turbo to the higher compression of the n/a block and efi set up like i have than to do a conversion.

- Suby Wan Kenobi
- General Member
- Posts: 1914
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Sunny Godwin Beach Qld
The Yanks have been adding the turbo to the NA bottom end now for a while but they seem to go through bottom ends quiet quickly so i would stick with the EA82T bottom end. All things considering the EA82T are not a bad motor and many people on this MB have used them for long periods of time and have been abusing them for even longer. They seem to last a long time if you make sure the head gaskets are fine and ring piston condition is fine.
[SIGPIC][/SIGPIC]
The long road ahead
The long road ahead
are the big end bearings different or is it just the fact that the turbo motor has a lower compression. if so could you get copper head gaskets made up that are thicker that would lower the compression of a n/a engine to allow a safe turbo bolt on? also are the carb heard and the efi heads different? if so are the efi and turbo heads the same.
yes i have a n/a car that has been converted to turbo (when i got it). Lag is fine around town -it spools up pretty quick being a small snail- and is just as fun to drive on the road as off. as for the annoying bits thats only because it obviously has lag and not as much torque as the ej series engines. it still gets through all right tho, just hasnt got the starting off power which helps in the slow stuff.
also as far as i know the heads are the same.
also as far as i know the heads are the same.

- Suby Wan Kenobi
- General Member
- Posts: 1914
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Sunny Godwin Beach Qld
what about the questions regarding the use of an EFI engine with thicker copper head gaskets to lower the compression to what a turbo motor would be. also are the heads the same on a turbo and efi engines? i dont want to sound like im harping but i was just thinking that it could be a fast and easy and cheaper way to get some more power. what about the big ends are they the same for an n/a motor and a turbo?
The heads on the turbo and NA EFI are essentially the same. The RHS turbo head has a couple of attachment points for oil and water feeds, that will need to be drilled and tapped on the NA EFI heads. Not sure how thick you'd need to have a copper head gasket to make a significant difference to the comp ratio, but one thing to remember with the boxer motor is that if you move the heads further out from the block with thick copper gaskets or what-ever you will start to have difficulties with things like the intake manifold that will no longer line up properly with the intake ports on the heads.
- Suby Wan Kenobi
- General Member
- Posts: 1914
- Joined: Tue Oct 04, 2005 10:00 am
- Location: Sunny Godwin Beach Qld