The ***ALL NEW*** AUSubaru.com.au Forums

Another issue I'd like to sort would be the making a post / thread 'sticky' ... :biggrin: The forum permission needed to achieve this would typically be applied to the moderators or admin groups. https://www.phpbb.com/community/download/file.php?id=202426&t=1 To apply Permissions : -group forum per...

Ramul wrote: ↑

Thu Oct 22, 2020 7:45 pm

thanks Guys,
Is there any other contact for Frog, I havent had much luck getting him through this forum.

Ramul

Andy Green Dom's Motors. https://www.domsmotors.com.au/contact/

TOONGA

read this https://www.clubsub.org.nz/forum/index. ... ification/

TOONGA

14l should get 140km minimum your carby is over fueling very badly. first thing you need to do is get the right jets, not just primary and secondary jets but the primary and secondary idle jets as well. then you need the correct air bleed screws and emulsion tubes. after that you need to get the cor...

if the coolant line is still connected leave it.

Coolant flows from either head through the manifold via a coolant channel.

I must ask did you get a Weber with the correct jets and venturis?

TOONGA

Looking really good!!! I noticed though that the cone in that rear disc was sitting out. I hope you did all of your castellated nuts up on the CV shafts to "I stood on the 4 foot long breaker bar after I did the nut up as tight as I possible could" otherwise you risk failure of all of your wheel bea...

Having seen one of these racks apart, it isn't putting it back together that is the problem. finding the correct seals is the issue. the later model racks are wider and cause steering geometry and bump stop problems. I have seen people use the electric steering column with a manual rack out of an En...

https://www.facebook.com/prospares/
or
https://www.ebay.com.au/str/prospareswa
or
https://www.facebook.com/subarinoAE/

contact them for the adapter plates

TOONGA

Merry Christmas and a safe and happy new year for 2020

To you and your family Bennie.

see you in the new year

TOONGA

welcome back SUBYDAZZ go to User Control Panel, then profile, then edit account settings.

Hope you have had a good christmas

TOONGA

sadly the images don't work for me either Bennie,

I will say they still work on the Ghost page

TOONGA

welcome to the board daniel270991

A video if you can of the noise in the area of the driver would be great. please don't do a Blair witch project and try to follow the noise, just have the phone set up in the general area of the noise and record the noise as it happens.

TOONGA

bumping so google can find this when people search for lift kits

TOONGA

bumping for the google bot to find and help people find info on lift kits for brumbys

TOONGA

Potential causes for this code to set are: Short to power in the signal circuit to the TBCPS sensor - possible Open in ground circuit at TBCPS sensor - possible Failed TBCPS Sensor - likely Failed PCM - unlikely

Read more at: https://www.obd-codes.com/p2565
Copyright OBD-Codes.com

TOONGA

Hi everyone, Just a quick update, I have the opportunity to get a 3.6ltr R engine, auto, loom etc... and would like to know if this will fit into the car (clearly there will need some custom work for the engine to bolt in, but just need to know if it is possible for it to fit with the auto and such...

looking really good Johnny T well done

TOONGA

moved from forum help to troubleshooting, as forum help is for help with the board.

TOONGA

Bennie not sure about the front end issue it could be torque bind or it could be a worn CV.

As for the centre diff they are full of silicone oil and it is possible it is leaking or has leaked.

TOONGA

Welcome back buddyboy, hopefully a few more people will start using the site again.

TOONGA