Search found 211 matches

by Gazza01
Sun Feb 05, 2017 9:16 am
Forum: Subaru Chat
Topic: Subaru Brumby Gearbox Mounts
Replies: 0
Views: 9241

Subaru Brumby Gearbox Mounts

I just bought 4 Subaru Brat Gearbox mounts in the USA online for $15.00 ea with postage $72 but exchange dollar will push it up a bit I guess. In Aus they ask $145 ea thats BULLSHIT - robbers. Try Subaru Brat for parts in USA or go Subaru Brat 1987 Rockauto and search. Postage and exchange dollars p...
by Gazza01
Sun Jan 22, 2017 5:29 pm
Forum: Subaru Chat
Topic: BRUMBY REAR DISC's
Replies: 7
Views: 4339

Thanks Toonga I have everything else but suddenly started looking for the rear disc's and realised I didn't have then. I been on ebay and see I can get RDA7554 Vortex Discs. Just got make sure they are right ones. Thanks lot anyway.
by Gazza01
Sun Jan 22, 2017 11:30 am
Forum: Subaru Chat
Topic: BRUMBY REAR DISC's
Replies: 7
Views: 4339

BRUMBY REAR DISC's

I have everything to set up my brumby with rear Disc's except rear Rotors . My question is Do I use Vortex rear Rotors RDA7554 or the front Vortex/Brumby Rotors RDA640.
by Gazza01
Sat Jan 21, 2017 6:41 am
Forum: Subaru Chat
Topic: Removing Speedo Cable from Gearbox.
Replies: 3
Views: 1989

Thanks Guys.
by Gazza01
Fri Jan 20, 2017 8:04 am
Forum: Subaru Chat
Topic: Removing Speedo Cable from Gearbox.
Replies: 3
Views: 1989

Removing Speedo Cable from Gearbox.

Removing gear box having difficulty removing speedo cable from side gearbox. Is it screwed in or is it push in. I dont want damage it .
by Gazza01
Sat Dec 17, 2016 2:29 pm
Forum: Subaru Chat
Topic: Remove Roller bearing from Brumby Pinion shaft
Replies: 4
Views: 2266

Yes looks more like what I'll have to do.
by Gazza01
Fri Dec 16, 2016 6:32 am
Forum: Subaru Chat
Topic: Remove Roller bearing from Brumby Pinion shaft
Replies: 4
Views: 2266

Yes its the left diff bearing thats really loose its a bit hard getting anything behind it. I have Jimy Slim bearing extractor it would fit behind the inner bearing race that fits onto pinion shaft if I could break/remove up the outer race and bearings. Got work out way without doing damage. Might h...
by Gazza01
Thu Dec 15, 2016 6:15 pm
Forum: Subaru Chat
Topic: Remove Roller bearing from Brumby Pinion shaft
Replies: 4
Views: 2266

Remove Roller bearing from Brumby Pinion shaft

I have rattling pinion bearing on one of my front Brumby pinion shafts. I need a way to remove the bad bearing without pulling down the gearbox if possible. Any ideas out there. Nothing on YOUTUBE on this one
by Gazza01
Thu Dec 15, 2016 10:06 am
Forum: Subaru Chat
Topic: Removing my Brumby Gearbox
Replies: 6
Views: 2918

Yes Toonga got that Thanks. I bought a Jimy Slim bearing extractor I toying with idea of removing the out race of that front pinion bearing and pulling the rest out with the narrow extractor. I can only see one pinion bearing each side then heating new bearing up to 200 degrees and dropping in. Coul...
by Gazza01
Sun Dec 11, 2016 10:47 am
Forum: Subaru Chat
Topic: Removing my Brumby Gearbox
Replies: 6
Views: 2918

Thanks a lot for that Toonga.
by Gazza01
Sat Dec 10, 2016 5:47 am
Forum: Subaru Chat
Topic: Removing my Brumby Gearbox
Replies: 6
Views: 2918

Removing my Brumby Gearbox

Got replace my gearbox old one is all rattly front, pinion shaft bearings and they bloody rattle. Thought was the CV shafts first but they OK the pinion shafts are just so loose bearing s are all loose. Got outer bearins but got get inner but in meantime have a gearbox in damaged Brumby thats OK so ...
by Gazza01
Tue Dec 06, 2016 8:15 pm
Forum: Subaru Chat
Topic: Gearbox short Driveshaft Stub
Replies: 4
Views: 2215

Yes got take that Circular diff ajustment plate off and see what Im up against. I can see that the outer seal is gone guess if outer bearing is gone so will the inner diff bearing. Not going waste time pulling it down have 3 spare boxes 2 are nice and tight. Just have a bit of an experiment might do...
by Gazza01
Sun Dec 04, 2016 11:44 am
Forum: Subaru Chat
Topic: Gearbox short Driveshaft Stub
Replies: 4
Views: 2215

There is a circular retainer plate round the Stub on the Brumby gearbox with a small holder plate with a bolt to prevent the circular retainer plater from screwing out. Searched Youtube but found virtually nothing on this subject except that the circular retainer plate will screw out however u must ...
by Gazza01
Sat Dec 03, 2016 12:46 pm
Forum: Subaru Chat
Topic: Gearbox short Driveshaft Stub
Replies: 4
Views: 2215

Gearbox short Driveshaft Stub

The short drive shaft stub that comes out of the side of the gearbox to connect with the CV Drive shaft is very loose and I get a awful rattle/vibration sound under acceleration when not under aceleration all is ok. I have just replaced driveshaft and all wheel bearings but it is still there and the...
by Gazza01
Fri Dec 02, 2016 6:27 am
Forum: Subaru Chat
Topic: Freezing CV Shafts to fit.
Replies: 15
Views: 5384

Im over these CV Shafts that don't fit easy and stuff up - Shonky Chow shafts. Im getting my CV Shafts from Suzukisuper now they slide through the Hud/Bearing fine none of this heating bearings bullshit. The Code I use when ordering is SB-8-901 they are chow but are manufactured by big Chow company....
by Gazza01
Sun Nov 27, 2016 10:21 am
Forum: Subaru Chat
Topic: Cv boot bands
Replies: 3
Views: 1862

Cv boot bands

Been looking at the prices of those CV Boot Clamps/Bands or whatever they call them On Ebay and they arn't very cheap, however I have access to plenty of rubber engine hose Band clips thats screw up. Wonder if I could use them.
by Gazza01
Sat Nov 26, 2016 8:59 am
Forum: Subaru Chat
Topic: CV Shafts
Replies: 2
Views: 1640

CV Shafts

Bought a couple of new Chow CV Shafts.When I tried to move the joints I could see how stiff there were and were rough to move so I decided to investigate. I released the boot clips and moved the boots back and was surprised to see that all that there was a small amount of black grease up against the...
by Gazza01
Thu Nov 24, 2016 10:03 am
Forum: Subaru Chat
Topic: another REPCO CV shaft stuffed 16months
Replies: 32
Views: 14287

That bit u mention about the heat from the exhaust playing part in CV life plays on my mind. On the drivers side u have the catalytic converter just below the inner CV boot.An old Subaru mechanic told me sometime ago that the heat from catalytic converter helps break down the rubber boot resulting i...
by Gazza01
Wed Nov 23, 2016 4:20 pm
Forum: Subaru Chat
Topic: another REPCO CV shaft stuffed 16months
Replies: 32
Views: 14287

I came across a pair of new CV shafts in my workshop made by Wanxiang Group China. Bought them through Suzukisuper they had a code of SB-8-901 and the slide perfectly through both hub bearings no forcing . Also I released both inner and outer boots by sliding back and added more of that Red CV beari...
by Gazza01
Mon Nov 21, 2016 8:59 pm
Forum: Subaru Chat
Topic: another REPCO CV shaft stuffed 16months
Replies: 32
Views: 14287

Cant for life of me understand how new cv shafts can *** up so quickly. Wot less that 100ks and clicking. This is Bull Sht Robbery Extortion.

Go to advanced search