The ***ALL NEW*** AUSubaru.com.au Forums

Got wheel alignment on young blokes 92 Brumby with a 2 inch lift kit. Cost $55. Mechanic said if u require a specialist wheel alignment then its Pedders or similar place. Does a Brumby with a 2 inch lift need other than a normal wheel alignment.

I don't know if the EA81 Brumby coil is that same but I got a TRIDON coil TIM-033 was OK. Just go to the TRIDON site and check.

I went to the trouble of pulling down a set of these elcheapo ebay brumby cv' and found that they did in fact have 6 bearings , but they were much larger that the genuine. The outer race was larger in diameter and they only had the LARGE snap ring up front of the race - no small snap ring behind it ...

Thanks Toonga will look at it.

Can anyone tell me out there if there are any special parts that are required to be added to the Brumby Gear box linkages. Just find that mine is pretty hard to get into reverse now that its been lifted 2 inches and not all that easy in other gears. Only has happened since I lifted it.

Yes its hard these days most parts arn't stamped with a brand and come in a fancy box. If u go to Bursons or Repco or other places the parts all look the same no brand name stamped on the ball joint or tie rod or tie rod end. Not sure that price is any guide either.

I'm looking for a set of Tie Rods for my Brumby. I've checked ebay and the prices vary from $14.00 to as high as $39.00. Can anyone out there give me some info buying tie rods .

I've bought 2 TWO sets of Brumby CV Drive Shafts of Ebay and as soon as I've installed them they continually CLUNK on 360 degree turns. All Imported Chow remanf shafts I guess. No such thing as genuine anymore but if I can get genuinely remanf drive shafts in stead of these shonky Ebay ones I'd be r...

I had trouble some time back getting a RWC because the outer rubber on the rim of the steering wheel was loose. I've still got the steering wheel, and its a really good original Brumby steer/wheel apart from the loose rubber rim. Any of you guys out there know how I can inject some adhesive compound...

Will the 5 spd L Series gearbox fit on to the motor of the Brumby and do any modifications have to be made.

Yes sounds good to me. Exactly what I did the tension reading on the tension bar was over and beyond the metric/nm markings on the bar.

Can someone confirm that the FRONT Castle nut on the Brumby has to be pulled up to 194nm. I recently got back the young fellows Brumby and the front Castle nuts were just finger tight. I had weird noises in the front. I subsequently pulled them up till my tension bar ran out of tension which was no ...

I'm over these crook replacement drive shafts. Were going back to the old days where the crooks are again doctoring up shonky CV Drive Shafts and selling them on Ebay and other outlets. I recently replaced the young blokes front CV Dive shafts on his Brumby only find they were knocking just after ab...

Looking for a spare carby for my 90 Brumby with a Hitachi Carby. Have a couple of EA82 Leone's in the local wrecking yard, and just wondering if any of those EA82 Carby's might be compatable with the EA81 Brumby Carby.

"DONE" exactly as u suggested and worked out fine. Thanks again.

Thanks a lot been trying to get my head round the easy/right way to do this.

The young fellow has bought a Brumby which has been lifted 2 inches. However and inspection reveals that the lift block on the top of the passengers side Shock absorber has been put in wrong way round resulting in the passengers side front wheel having a bad inward camber. The drivers side front whe...

I just replaced two bushes on my front control arms on my Brumby and I didn't find it an easy job. First I had to remove the rubber centre piece as the outer metal tube/sleeve would not budge without doing any damage to the control arm. Once I removed the rubber bush I got out my Recipro cordless sa...

Ive stripped a few down and swapped parts round to get a good shaft, and have no hestatition in dropping a cv shaft to replace the boot. No way I'd throw a good CV shaft away just because the boots busted. Its a messy job but I followed up on this CV shaft repair after going on YOUTUBE. The only pro...

I bought 2 front drive shafts on Ebay for total $250.00 thats $125 each. I see some for $95 and some up to $185. How can u tell the the expensive ones are better than the cheapies.....Its got me. Seems like a great rip off by the people that sell then for $185 if they are only the same as the cheapi...