Ummm....they fit fine my RX turbo with 205/50/15Venom wrote:15" 505 gti rims stick out past the guards on l series.
Search found 74 matches
- Thu Aug 30, 2012 7:47 pm
- Forum: Brakes, Wheels and Tyres
- Topic: questions on peugeot wheels
- Replies: 16
- Views: 5991
- Fri Jan 16, 2009 11:15 am
- Forum: Engine, Gearbox and Diff
- Topic: Identifying L series gearboxes, 3.9 or 3.7?
- Replies: 7
- Views: 2432
- Fri Dec 26, 2008 6:29 pm
- Forum: Electrical, Wiring and Lighting
- Topic: Help Please - Reverse Lights
- Replies: 11
- Views: 3705
Try shorting out the connector on the main loom. If your reverse lights come on, then all is good on the car side and the gearbox switch or wiring is at fault. If your reverse lights don't come on when you short the connector, you have a problem in your loom/fuse/reverse lights somewhere. To test th...
- Tue Nov 18, 2008 9:09 am
- Forum: Engine, Gearbox and Diff
- Topic: Reputable Ea82T cv shaft suppliers?
- Replies: 4
- Views: 2007
- Tue Oct 28, 2008 7:00 pm
- Forum: Brakes, Wheels and Tyres
- Topic: Peugeot Alloy Rim Wheelnuts
- Replies: 4
- Views: 2021
- Sat Oct 25, 2008 3:16 pm
- Forum: Brakes, Wheels and Tyres
- Topic: Peugeot Alloy Rim Wheelnuts
- Replies: 4
- Views: 2021
Peugeot Alloy Rim Wheelnuts
Any use standard RX "H" mag wheel nuts on Peugeot 15" alloys?
I've got the original pug nuts, but the Sub ones look better
I've got the original pug nuts, but the Sub ones look better
- Fri Oct 24, 2008 8:53 am
- Forum: Victoria
- Topic: Stripping My L-series
- Replies: 25
- Views: 5938
- Fri Oct 03, 2008 7:36 am
- Forum: Trouble Shooting
- Topic: EA82T problems
- Replies: 5
- Views: 1662
I'd have a close look at fuel pump or partially blocked pickup. Probably best to check fuel delivery pressure under acceleration if you've got a gauge. I was crewing for a WRX in the ARC and they had a similar problem. Turned to be a piece of what looked like indicator lens in the fuel pickup pipe. ...
- Thu Oct 02, 2008 2:42 pm
- Forum: Engine, Gearbox and Diff
- Topic: EA82 drive shaft, CV and bearing
- Replies: 2
- Views: 1107
EA82 drive shaft, CV and bearing
Finally got the roll pins out of the gearbox end and have knocked out the right drive shaft from the hub. Unexpectedly, the inner front wheel bearing came out with the shaft. doh! Since this my first shaft replacement, not sure if that is supposed to happen. So now I need to know if the the bearing ...
- Wed Oct 01, 2008 4:08 pm
- Forum: Engine, Gearbox and Diff
- Topic: EA82 gearbox roll pin help
- Replies: 6
- Views: 1682
Sometimes people not in the know put the Cups in 180degress out, the pin will go in but not all the way through meaning that to remove the pin it must be punched out the opposite way to which it was incorrectly belted in. The catch is you have to guess which way it needs to be bashed out. That woul...
- Tue Sep 30, 2008 11:02 pm
- Forum: Engine, Gearbox and Diff
- Topic: EA82 gearbox roll pin help
- Replies: 6
- Views: 1682
EA82 gearbox roll pin help
Ok, so I got one roll pin out OK and the CV off one side of the gear box (piece of cake with the engine out) The other roll pin seems to be made of super strong unobtanium and is wedged tight. I've belted it, drilled it, sworn at it in English, French, German and a special made up language I've got ...
- Tue Sep 30, 2008 10:56 pm
- Forum: Open Slather
- Topic: Top Gear Australia- whatd ya think?
- Replies: 52
- Views: 10396
- Tue Sep 30, 2008 6:02 pm
- Forum: Conversions, Modifications and Performance Upgrades
- Topic: DR AWD box install tomorrow .
- Replies: 43
- Views: 7743
- Tue Sep 30, 2008 2:42 pm
- Forum: Conversions, Modifications and Performance Upgrades
- Topic: DR AWD box install tomorrow .
- Replies: 43
- Views: 7743
D/R to AWD RX conversion - EA82T
To use these gearboxes in an Aus spec L RX Turbo you have to modify the shift mechanisms stay or steady bar because the lower rear of the AWD transmission is deeper and longer than the part time box to house the center differential . The upper rear of the box where the tailshaft slides in is dimens...
- Tue Sep 02, 2008 11:55 am
- Forum: Conversions, Modifications and Performance Upgrades
- Topic: Fitting EA82 MPFI TB to Spider plenum manifold .
- Replies: 16
- Views: 4155
- Mon Sep 01, 2008 2:59 pm
- Forum: Engine, Gearbox and Diff
- Topic: Engine Cleaning
- Replies: 11
- Views: 2874
- Sat Aug 23, 2008 6:21 pm
- Forum: Subaru Chat
- Topic: Liberty RS Ute
- Replies: 12
- Views: 4762
- Thu Aug 14, 2008 11:18 am
- Forum: My Subi
- Topic: H6 powered Gen 2 Liberty.
- Replies: 21
- Views: 9772
And secondly, a factory H6 gen 3 outback can be converted to dual range manual. The only problem with the latter is that in high spec cars with stability control I doubt the VDC or ABS will work without the auto present. I've been considering doing a manual H6 Outback for a while but didn't think o...
- Tue Aug 05, 2008 4:13 pm
- Forum: Subaru Chat
- Topic: Anyone ej'd an L in victoria?
- Replies: 17
- Views: 3546
- Tue Aug 05, 2008 1:59 pm
- Forum: Subaru Chat
- Topic: Anyone ej'd an L in victoria?
- Replies: 17
- Views: 3546
>3 Do the brakes need upgrading for a ej22? Damn right they do, I'd seriously consider 5 stud but at a minimum RX rear discs. Not sure the RX discs would make much difference, as most of the braking power is directed at the front anyhow. It's also worth keeping in mind that drums can often have a m...