The AUSubaru.com.au Forums

Yep standard blade fuses, same as under dash in the L series

Ive done Moreton a few times in an L series. Without a serious suspension lift, and LSD/locker of some sort it can be fun on the inland roads where the big 4x4's and tour trucks dig massive ruts. Mid day the sand can be very hot and thus slippery too. If your well equipped, keep a level head when yo...

...is it a single input for all the blade fuses Yep works quite well, I like things neat as I can to my ability. Ebay, search fuse block . This one is a Blade terminal, ring terminal under screws would have been better. This one is a 6 way. Some also have a ground bar, but I find that unnecessary i...

Discrete switch dash mounted. Led lights when either 1 or two fans powered. https://imagizer.imageshack.us/v2/535x401q90/538/WUp3Zi.jpg LED is BRIGHT at night, some dull red paint might do the trick. Would not be so bad were it mounted at a lower "out of face" location. https://imagizer.imageshack.u...

Sorted, thanks Jonno!

27x8.50R14 NANKANG A/T +1 on the Nankang, I have them on the front of the L, good hard sides of the tread, meaning the bad camber has more meat to chew on. LT construction. I also got mine from Bob Jane, price seems about what I paid also. Was a special order that came from Newcastle. I can only co...

taza wrote:It's a single piece, doesn't have a centre bearing??...

IC, showing how little I know about MY specifics.
Hard when these issues crop up, on the up side car will be sweet when you solve it, with all the replaced parts. Hard on the wallet though.

What does the tail shaft center bearing look like? Mine rattles/flogs about when car is heavily loaded and engine us under load in 4wd. Imagine it would be way worse in rwd.

Have you lay under the car, engine running. Someone steering lock to lock with the car stationary. Most of these ideas mentioned would make some type of noise. Perhaps that might help track the area/cause.

steptoe wrote:two question marks at the end of that little statement turns it into a question. Surely it is not in the realm of some of the cryptic stuff I write ?

Had to laugh at that one mate!

El_Freddo wrote:Andrew_T did a good write up about it ages ago. I'd drop a link in here but I'm on my phone so searching isn't fun or easy...

showthread.php?t=4177

Update on this, likely nothing to do w S1/S2. My car was factory auto, no HHV. So looking for one from an auto w 4 ports, two drivers side, two bottom.

I need one with four ports, two D side, two bottom. Car was auto from factory, hence no HHV.

Looking for a master cylinder for a series 1 L series. The series 2 seems to have less inputs due to the HHV. Pic of mine below, showing the four ports needed, S2 has 3 (#3 is not tapped). Reply here or PM. If none available, I'll change the brake lines under the hood and install the HHV, but hoping...

Hey Champ, dont have a S1 L Brake master cylinder in decent nic by chance?
S2 brake lines look to be diff due to HHV.

I've got a smooth 93 L series second gen. Is there a difference between touring wagon and non?

Edit: I'm in Penrith NSW

Hey champ, what a crap day hey. Nice that the office was normal and gave you some rest from the woes. Its times like these that professional help or least help from a forum member that knows the issue or has the skills to diagnose and take the stress off you really helps. You have done the right thi...

...relays with a fuse socket in the front so incoming power through pin 30 goes via the fuse... Thx for the heads up Jono, see this thread for a rough diagram of my drivers side fuse panel (inc fuses), relays will sit just a few cm away. Needless I do have one of these fused relays that I do a bit ...

Thanks for the responses guys. I was busy prepping for the trip and never came back to finish this thread. Quick update, not enough pics, as usual I didnt take any of the wire runs front to back etc. What I ended up with is two separate and dedicated runs of both pos and neg, one for the anderson an...

Hello fellow Soobi fans. Been too long since I've had time to play with my car let alone do some posts :( I'm putting in manual controlled thermo fans, twin relays and an 1/off/2 dash switch, no auto. How does the below diagram look? LED was an afterthought. At first I though an illuminated switch b...